← Back to Blog
Engineering 2026-05-03 3 min read By Konvertibly Team

Hydraulic Pressure Calculator: Force, Area, and Pascal's Law

Calculate hydraulic pressure, force output, and cylinder area using Pascal's Law. Includes worked examples for hydraulic cylinders, jacks, and piston systems.

Hydraulic Pressure Calculator: Force, Area, and Pascal's Law

Pascal's Law and Hydraulic Systems

Pascal's Law states that pressure applied to a confined fluid transmits equally in all directions. This lets a small input force generate a massive output force using area multiplication.

Core Formulas

Pressure:    P = F / A   (Pa or PSI)
Force:       F = P Γ— A   (N or lbf)
Area:        A = F / P   (mΒ² or inΒ²)

Pascal's Law:
F_out / A_out = F_in / A_in
β†’ F_out = F_in Γ— (A_out / A_in)

Hydraulic Jack Example

Input piston: A = 0.001 mΒ², F = 200 N
P = F/A = 200/0.001 = 200,000 Pa

Output piston: A = 0.1 mΒ²
F_out = 200,000 Γ— 0.1 = 20,000 N (β‰ˆ2 tonnes)
Mechanical advantage = 100:1

Cylinder Force (Double-Acting)

Extend: F = P Γ— (Ο€ Γ— dΒ² / 4)
Retract: F = P Γ— (Ο€ Γ— (dΒ² - d_rodΒ²) / 4)

100mm bore, 50mm rod, 200 bar (20 MPa):
Extend: F = 20e6 Γ— Ο€ Γ— 0.01 / 4 = 157,080 N (16 tonnes)

Common Hydraulic Pressures

  • Car brake system: 10-15 MPa (1450-2175 PSI)
  • Hydraulic press: 10-70 MPa
  • Construction equipment: 20-35 MPa
  • Aircraft landing gear: 35-70 MPa (5000-10000 PSI)

Calculate hydraulic pressure: Free Hydraulic Pressure Calculator

Pascal's Law and Hydraulic Advantage

Pascal's Law: pressure applied to an enclosed fluid is transmitted equally in all directions. Hydraulic force: F = P Γ— A. A small piston (area A₁) at pressure P exerts force F₁ = P Γ— A₁; a large piston (area Aβ‚‚) at the same pressure produces Fβ‚‚ = P Γ— Aβ‚‚. Mechanical advantage = Aβ‚‚/A₁. Example: a 50 cmΒ² master cylinder at 100 bar (10,000 kPa) produces 5,000 N force; connected to a 500 cmΒ² slave cylinder, output force = 50,000 N (10Γ— mechanical advantage). This principle powers hydraulic jacks, excavator arms, aircraft landing gear, and automotive brakes.

Common Hydraulic Pressures

  • Automotive brakes: 100–150 bar (1,450–2,175 psi)
  • Industrial hydraulics: 140–350 bar (2,000–5,000 psi)
  • High-pressure hydraulics: 350–700 bar (5,000–10,000 psi)
  • Water hydraulics: 100–200 bar
  • Pneumatic systems (air): 4–10 bar (58–145 psi) β€” much lower than oil hydraulics

Frequently Asked Questions

What is the difference between hydraulic and pneumatic systems?

Hydraulic systems use incompressible liquid (usually mineral oil); pneumatic systems use compressible gas (usually air). Hydraulics can transmit much higher forces and hold position under load precisely (liquid doesn't compress). Pneumatics are lighter, cleaner (no oil spills), and faster in action but spring back when load is released (air compresses). Hydraulics are used where high force and position holding matter; pneumatics for high-speed repetitive motion in lighter applications.

What causes hydraulic system failure?

Contamination is the leading cause β€” particles as small as 5–15 microns can score valve bores and accelerate wear. Contamination enters through breathers, seals, and maintenance. Oil analysis and filtration management are central to preventive maintenance. Air in the system (aeration) causes spongy response and accelerated oil degradation. Seal failure from temperature extremes, chemical incompatibility, or mechanical damage causes external leakage and pressure loss.

How do hydraulic accumulators work?

An accumulator stores pressurised hydraulic fluid (against a gas pre-charge or spring) to supply sudden peak demands, compensate for leakage, and dampen pressure shocks. Common types: bladder (rubber membrane separates gas from oil), piston, and diaphragm. Pre-charge pressure is set to ~60–90% of minimum operating pressure. Accumulators must not be confused with reservoirs β€” they store pressurised energy and are dangerous if discharged suddenly.